My dilemma is - should I upgrade my reciever or just get for instance, an dedicated sub EQ like the SVS AS EQ1 or would a new AVR serve my purpose plus HDMI 1.4 etc. As to what crossover to set for your speaker/sub combination, I would start with 80 Hz. I've got a few sub-related puzzles to solve: 1) Currently I have one, big expensive sub with the left wide speaker sitting on top of it. I own 2 subwoofers. They are in the 3SP Mix mode. If you wish to use the calibration systems in any of the subs, you should do that first before running Audyssey. I'll try a third time but with more mic positions (Iused 4-5 above) and if it is still sounding tinny - what's next? Hi folks. Likewise, I could set it do nothing -OR- to a +6db @ 25Hz to give it a bass boost but that does not help with removing the 42Hz Peak. The receiver does not give me the option to turn OFF LFE+Main. Phase The phase control in a powered subwoofer allows the user to add electrical delay to the incoming signal. Receiver: Denon AVR-590. One is in the front right corner and other is in the back left corner. I ran Audyssey on the Denon AVR-2807. There is no such thing as a "sub crossover". The suggested crossover frequency for the main speakers was 40 Hz, which I manually changed to 60 Hz after runing Audyssey. the distance setting is 30ft, with a +6db settings. What I mean is, can the multieqxt EQ 2 subs? Many powered subwoofers have controls that are set manually. Been trying to google but getting lots of endless links.. With the AVP I have them all of them set to LFE+Main. Sub distance (delay) will usually measure longer. Also, MultEQ will not apply correction to the main speakers below the roll off point that it measured. Generally with dual subs, if what you want is not necessarily better bass or … LFE–THX or LFE+Main. Does this mean that this is the right phase/delay setting? This is normal and is part of the correction that MultEQ performs to make sure that signals from all speakers and subs are arriving at the main listening position at the same time. There is no mic pass-through connection needed and no need to connect 1a to 1b. I've just got a BK XXLS400-FF, my first decent sub, and I'm trying to set it up. Does Audyssey measure phase of the sub? Note: Before running Audyssey MultEQ, be sure the subwoofer's controls are set with the crossover frequency at its highest value and the phase setting at zero degrees (unless your experiments have convinced you that you will get a better result with a different phase setting). Luke in Tech Support can help walk you through these steps. I have to agree with Bill that the connections for the Audyssey sub eq on page 10 are confusing. Can you point me in direction of an AVR which has MultiEQ XT and the dual sub EQ feature? I ... adjusting advice Amplifier audio Audyssey AVR best bookshelf Component controversy crossover deep denon Double Bass Ed Mullen electronics entertainment filter frequency full range towers help home hometheater101 huge information Large Vs Small LFE + Main onkyo passive radiator prime reciever … My left and right front speakers would always be out of phase to Audyssey since it is a multi-driver design (Raw Acoustics RA8). Before - it sounded great. Also, I spoke to Installer support at Audyssey today and they told me that I can calibrate my subwoofer separately without being connected to my AVR. Subwoofer phase knob I ran Audyssey on the Denon AVR-2807. Yes, if the AVR with MultEQ XT provides individual control of the two subwoofers then MultEQ XT will create filters for each sub separately. The reason for the longer distance is because the processing in your sub adds delay to the signal. That is only half of a crossover. If you wish to use processing in the sub, then it should be done first prior to running MultEQ. There are a lot of recommendations out there for a two-sub system. At the end of calibration, Audyssey says that Subwoofer 2 is at 12.3ft from listening position and Subwoofer 1 is at 0.7 ft from listening position. If you have a preference for more bass that is higher than reference then you can change it, but you will no longer be listening to the content the way it was mixed. This too seems odd, as I'd expect the trial and error results without Audyssey filters to be tainted. So what about the eq on the subwoofer settings should i run the audyssey with flat, punch , or depth? I had set the gain on the back of the subwoofer halfway and crossover all the way up. The Audyssey processor requires the MultEQ Pro Installer kit (sold separately). I did this and the Audyssey readings were fairly good, so I left them alone. Probably best to leave that knob at 0. For more subwoofer set up tips please look here. You need to get an SPL meter and dial the subwoofers at around 85dB (setting the levels), also playing around with the phase so that they're matched together, this can be much more difficult to do when both subwoofers are up front in the room. The other part is you need to manually dial in each subwoofer prior to running audyssey. I used Audyssey to calibrate my system, Denon AVR-X4100W with 9 channels (4 ceilings and 5 floors, with 2 Subwoofers, both located next to Front Left and Right speakers). My current Onkyo 577 is hooked up to these 2 subs using a Y cable and calibrated using 2EQ, but I'm looking to upgrade to a better 7.2 receiver with MultiEQ that can apply sub freq corrections to improve the experience. The "Bass Management Boot Camp" article about subwoofer setup that I wrote for the November S+V inspired an in-turn inspiring e-mail from reader Bruce Erwin. I have Audyssey Sub EQ and Integra DHC 9.9 with Pro insalled. also i thought that it was a good idea to get the audyessy to set the subwoofer gain between -3db to +3db? Yes, that is the preferred method even if you have two sub outputs on the AVR. To get the best of both worlds you will need to move to an external Sub Equalizer. And when running the Pro in Integra, do I still leave this cable hooked up? If they're going to be calibrated together, then would you suggest that I need to first run Audyssey with one sub connected at a time and get them to the same db levels by tweaking volume controls on the sub, then run finally Audyssey MultiEQ with both of them connected together ? Try to set the volume control on each sub to the same position so they play at the same level as each other. Audyssey seems to set it far to quiet! The diagram show everything and does not explain what not to hook up if you have the Audyssey Pro Kit. I have done this 2x now and still get lost. It was used as an LFE sub when I had my Lexicon MC12. Two of subs sitting next to the front B&W 800's (Velodyne Digital Drive 15's) have a mic menu calibration system. My sub is the Rythmik Audio servo … There is no difference in performance. Yes I could go and remeasure everything with the sub phase reversed but hope someone could shortcut an answer. When you calibrate it with 180 phase is Audyssey just setting the level lower? For a list of new AVRs with Sub EQ HT please check here. I don't think you will get much benefit by applying a single parametric band cut and certainly would not recommend adding a parametric boost. Should I leave this setting, or move the phase control knob back to 0°?. He also suggests a trial and error approach to sub placement before running Audyssey for the loud, crisp bass position.