5. ASTM B 368 - Standard Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test). Acceptable Manufacturer: Trulite Glass & Aluminum Solutions, which is located at: 403 Westpark Ct. Suite 201; Peachtree City, GA 30269; Toll Free Tel: 800-432-8132; Tel: 678-593-9200; Email: request info ([email protected]); Web: www.trulite.com. Testing: Testing shall be performed per AAMA 503 by a qualified independent testing agency. Verify openings are sized to receive entrance system and sill is level in accordance with manufacturer's acceptable tolerances. Product: Aluminum Framing System Resistor� Series SW732 Aluminum Curtain Wall as manufactured by Trulite Glass & Aluminum Solutions. Manufacturer's Field Services: Upon Owner's request, provide manufacturer's field service consisting of product use recommendations and periodic site visit for inspection of product installation in accordance with manufacturer's instructions. 20 25 30 35 40 45 50 55 60 65 70 Protect installed products until completion of project. (Standard), Clear Anodizing Coating Conforming to AA-M12C22A31, AAMA 611, Clear Anodic Coating (Clear #04) (Standard). Trim piece. Align assembly plumb and level, free of warp and twist. Do not begin installation until substrates have been properly prepared. Some common infills include metal panels, louvers, and photovoltaic panels. If your project requires a one of a kind design than laser fused profiles are your answer. ASTM E 1996 - Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes. Home | Products | System Profiles | Curtain Wall Steel Profiles. Prepare components to receive anchor devices. Conduct tests for air infiltration and water penetration with manufacturer's representative present. inward and (____) P.S.F. There shall be no leakage at a static air pressure differential of 20 PSF as defined in AAMA 501. Weep holes shall be located in the horizontal pressure bars and covers to divert water to the exterior of the building. Clean surfaces thoroughly prior to installation. Member Wall Thickness: Each framing member shall provide structural strength to meet the specified performance requirements. Product Data: Manufacturer's data sheets on each product to be used, including: Preparation instructions and recommendations. Laws and building and safety codes governing the design and use of Kawneer products, such as glazed entrance, window, and curtain wall products, vary widely. Water Drainage: Each light of glass shall be compartmentalized by using end dams at horizontal/vertical joint intersections and silicone sealant to divert water to the horizontal weep locations. Water Resistance: The test specimen shall be tested in accordance with ASTM E 331. • Curtain wall intersection at wall. AAMA 2604, Fluoropolymer Powder Coating. The following is one example of how a mock-up on a large project might be specified. Powder coatings are an EPA recommended finishing method for architectural aluminum and further contributes towards the "green building initiative" of the U.S. Government. outward. Air infiltration rate shall not exceed 0.03 cfm/sf at static air pressure differential of 6.24 P.S.F. ... No other technology allows you to unfold your design on steel or stainless steel curtain walls like laser fusion. Fabricate anchors. When steel anchors are used, provide insulation between steel material and aluminum material to prevent galvanic action. ** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section. ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference. If an enemy reached the foot of the wall, they became difficult to see or shoot at directly, so some walls were fitted with a projecting wooden platform called a … Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns. Consult with your Trulite Glass & Aluminum Solutions representative for other surface treatments and finishes. Material Standard: ASTM B 221, 6063-T6 alloy and temper. Air Infiltration: The test specimen shall be tested in accordance with ASTM E 283. Bare Mullion. (Color: __________). Strap Anchors are not allowed for use with Hurricane Impact-Resistant Systems. With its unmatched product line, Trulite has created a Total System Approach to satisfy virtually any architectural glazing requirement. Fabrication Tolerances: Fabricate aluminum framing in accordance with framing manufacturer's prescribed tolerances. Field Measurements: Verify actual measurements/openings by field measurements before fabrication; show recorded measurements on shop drawings. Uniform Load: A static air design load of +70/-80 P.S.F. Refer to Division 1 Testing Section for payment of testing and testing requirements. All profiles have sharp crisp corners, clean shadow lines and smooth almost invisible weld seams. Rectangular hollow sections are a very popular design on façades. Do not install products under environmental conditions outside manufacturer's absolute limits. Protect entrance doors against damage from elements, construction activities, and other hazards before, during and after entrance installation. Weather-tight Construction: Install curtain wall system and other members in accordance with manufacturer's installation instructions to ensure weather-tight construction. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements. Glass Type: 1 inch (25 mm) insulated glass of construction indicated or scheduled. The design pressures are based on the (____) Building Code; (____) Edition. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. Site Verification of Conditions: Verify substrate conditions (which are specified to be installed under other sections) are acceptable for product installation in accordance with manufacturer's instructions. Wrapped mullion. Fasteners: Where exposed, shall be Stainless Steel. Laser fused rectangulars not only have perfect sharp outside corners independent from thickness but can be optimized to the requested loads by increasing wall thicknesses were required. This section is based on the products of Trulite Glass & Aluminum Solutions, which is located at: TRULITE GLASS & ALUMINUM SOLUTIONS is one of North America's largest architectural glass and aluminum fabricators and distributors. Trim Piece. ** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required. Accurately fit and secure joints and corners. Storage and Protection: Store materials protected from exposure to harmful weather conditions. A curtain wall is defined as thin, usually aluminum-framed wall, containing in-fills of glass, metal panels, or thin stone. Includes perimeter trims� stools� accessories� shims and anchors� and perimeter sealing of curtain wall framing. Air infiltration rate shall not exceed 0.06 cfm/sf at a static air pressure differential of 6.24 PSF. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. No uncontrolled water leakage is permitted when tested at a static test pressure of two-thirds the specified water penetration pressure but not less than 8 PSF. Interior Spacer shall be compatible with Silicone Sealant. Provide vertical butt glazed assembly as indicated or scheduled. Storage and handling requirements and recommendations. The wind and gravity loads of the curtain wall are transferred to the building structure, typically at the floor line.